Compared with traditional ovens and similar equipment, our company's pasta infrared tunnel oven has the following advantages:
1. The baked product is heated both inside and outside, the temperature difference between the inside and outside is small, does not deform, does not change color, and has stable quality;
2. Fast baking speed and high efficiency, which can save about 2-6 times and greatly shorten the production and shipping cycle;
3. Local heating, less energy waste, saving more than 30% of electricity;
4. Due to the large amount of energy transmission per unit area, it is small in size, saves space on the site, and saves construction costs;
5. It can be connected to the production line and used for synchronous control to reduce defects;
6. The temperature can be controlled in sections to meet the needs of the product, with high flexibility;
7. Forced ventilation device, less solvent residue, no danger, explosion-proof, environmental protection;
8. The exterior temperature of the casing is close to the ambient temperature, the working environment is comfortable, and the energy waste is reduced;
9. The product does not need to stand before baking, shortening the working hours and reducing pollution;
10. Stepless constant temperature control system is adopted to ensure stable product quality.
HY-K02 Noodle Cake Infrared Tunnel Furnace-Features:
1. Infrared lamp: vacuum-plated infrared enhanced film on the outer surface, the length can be set according to customer requirements. Continuous working life over 6000 hours.
2. High temperature line: 62, 42 national high temperature line.
3. Unique built-in fan design, safe and reliable, clean furnace cavity.
4. The product is professionally used for baking high-frequency, low-frequency, transformer and hardware plastic products.
5. Full-automatic temperature control, which saves 2-5 times longer than traditional vertical oven, saves power by more than 30%, and has high work efficiency.
HY-K02 Noodle Cake Infrared Tunnel Furnace-Parameter Dimensions: L6000mm * W900mm * H1250mm.
Baking area size: L4800mm * W700mm * H150mm.
The material placement area is 600mm in front and 600mm in the rear, and stainless steel plates are installed in the discharge area and the discharge area.
The entrance and exit are equipped with height adjustment plates with an adjustment range of 30-100mm.
The surface of the inlet and outlet is SUS201 = 1.5mm protection board.
The number of sections of the body: 2 sections. It is divided into 3 baking areas, the first 250MM low temperature area, and the last 2 constant temperature areas.
The furnace body uses 1.5mm / 1.2mm galvanized sheet to bend and weld the outer upper chamfer.
The fuselage is made of Fangtong, and the structure is designed in sections to facilitate disassembly and installation.
An adjustable caster and foot cup is installed at the bottom for easy carrying and positioning, and height and level adjustment.
The color of the baking powder (plastic spray) of the fuselage is high-gloss gray (other colors are provided as a sample).
Dustproof, safe, beautiful, hanging buckle structure installation, easy maintenance and combination.
The furnace body is sealed with imported silicone.
The inner wall of the furnace is 1.2mm SUS201 stainless steel, and each infrared lamp is equipped with a stainless steel reflector.
A handle is installed on the other side of the furnace body hinge for easy maintenance.
Power: 1 / 2P Taiwan Dongyuan inverter and 1 / 2P motor.
Conveying speed 0.2 ~ 3m / min (adjustable by frequency conversion)
Reducer: 1200: 1 A set of reducer, speed adjustment mode: variable frequency speed adjustment, precise speed adjustment.
Conveying carrier: The conveying bandwidth is 700mm, and a 30 * 15 stainless steel flat pass is used with a pitch of 46mm. 6 points double pitch high carbon steel chain on both sides ...
Conveying sprocket adopts tooth surface carbonized standard sprocket, and the main shaft is made of cold drawn steel.
The conveyor head adopts the spiral method to adjust the tightness of the mesh belt, which is beautiful and durable.
HY-K02 Noodle Cake Infrared Tunnel Furnace-Commissioning Steps
1. Three-phase five-wire system (three-phase 380V) connected to the power, the hot wire is connected to the main switch, the neutral line is connected to the neutral line, and the ground line is connected to the ground line.
After turning on the power, check whether the transmission line is blocked. Press the start switch to see the motor running direction,
If there is no operation, the phase sequence is wrong, please switch two of the three-phase power lines;
2. Adjust the conveying time. Adjust the rotary terminal on the digital display controller, observe the change of the value, and calculate the time required for the material to flow out according to the speed.
Set temperature: press SET --- SV flashes --- move the arrow button to set the required temperature --- press SET to complete the setting.
Temperature correction: Measure the actual temperature at the temperature sensor. If the difference between the displayed value and the displayed value is greater than 5 degrees, you need to modify the compensation value.
Temperature correction method: If the actual measured temperature is 125 degrees and the temperature meter shows 120 degrees, then set the SC parameter to 5
The actual measured temperature is 125 degrees, and the temperature meter shows 130, then set the SC parameter to -5.
Reminder: change the offset parameter value. It will directly affect the temperature in the furnace. Please set the temperature accurately.
Re-verify to avoid the scrapped material being baked due to high temperature.
4. Institutional adjustment of exhaust gas discharge port adjustment: The exhaust gas discharge port has a regulating damper, which is generally fully open.
If the temperature does not reach the set value, you can reduce the diameter of the damper according to the direction indicated by the arrow.
However, you cannot reach the small position, where the damper is fully closed, and there is a danger of explosion due to too high solvent concentration.
5. Operating steps
1 Turn the air switch handle to the ON position, turn on the main power, and the power indicator light is on.
2 When turning on the machine, turn on the power switch, and then turn on the conveyance control switch (it is not necessary to enable it)
Turn on the hot start switch again, each indicator light is on, and it enters working state.
3 When stopping, turn off the heating first, then turn off the transfer switch, and then press the emergency stop to stop the machine.
Technical customer service:
Enterprise Enterprise: email@example.com
Our after-sales: free warranty within 12 months, lifetime service!
Some cases of Huiyue:
1. Shenzhen Pufengrui Technology Co., Ltd.-Purchase 3 HY-K02 infrared tunnel furnaces
2.Shenzhen Wanzhiyu Technology Co., Ltd .—— The number of employees has been reduced from 200 to 130, and the average output can be increased by 0.5 times.
3. Dongguan Dazhong Electronic Technology Co., Ltd. ——A direct branch of Huawei Electronics, with an annual comprehensive output of more than 80,000K,
Purchase our 8 HY-K02 Infrared Tunnel Furnace Some customers of Huiyue Video:
Huiyue impregnation tunnel furnace integrated machine: http: //www.hvyes. . cn / 彩乐乐网 / 彩乐乐网143.htm
Video of circuit board infrared tunnel furnace: http: //www.hvyes. . cn / 彩乐乐网 / 彩乐乐网104.htm
Huiyue infrared tunnel furnace startup video: http: //www.hvyes. . cn / 彩乐乐网 / 彩乐乐网102.htm
Video of Huiyue Foods Infrared Tunnel Furnace: http: //www.hvyes. . cn / 彩乐乐网 / 彩乐乐网99.htm
Infrared oven quality manufacturer: http: //www.hvyes. . cn /
Automatic casing machine manufacturer: http: // www. . cnhuiyue. . com /
Manufacturer of automatic vacuum impregnation machine: http: //www.huiyuecn. . com /
pcb tunnel furnace drying line
Stainless steel mesh belt tunnel furnace
Commissioning site of infrared tube furnace
Tunnel furnace transformer drying line
Stainless steel mesh belt tunnel furnace (encrypted)
Professional custom non-standard infrared tunnel furnace
Stainless steel square tunnel tunnel furnace
IR infrared tunnel furnace scene picture
Infrared oven tunnel furnace diagram
Transformer assembly line drying line
Huiyue Tunnel Furnace Working Diagram
Smart Tunnel Furnace Control Panel
Huiyue Tunnel Furnace Timer
Tunnel furnace inverter debugging
Huiyue Tunnel Furnace Box Protection
Dongguan Tunnel Furnace Plant