( 图示 ) Mixer sheet extruder, plastic sheet equipment ( pictured )
邱晓娟 ：一九九六一九七七） ( Qiu Xiaojuan : 1996, 1977)
恭乐橡塑机械有限公司的密炼机目的：规范化的设备操作及设备的维护保养，其目的就是确保设备的正常运作与延长寿命，降低维修成本与提高生产效率。 The purpose of the mixer of Xuzhou Gongle Rubber & Plastic Machinery Co., Ltd. is to standardize the operation and maintenance of the equipment. The purpose is to ensure the normal operation of the equipment and extend its life, reduce maintenance costs and increase production efficiency.
2. Scope of application: Operation guidance applicable to rubber and plastic mixer equipment
3. Special responsibilities: The special equipment operators and maintenance personnel designated by the user shall not violate the rules and operate the equipment skillfully, and the irrelevant personnel shall not approach or disturb the responsibilities of the equipment.
Fourth, the operating details: 1. Turn on the power one by one. If you need to warm up, set the temperature and observe whether the heating is normal. If the water is cooled, open the inlet and outlet valves for normal water flow. 2. Clean up the mixing room. Do not use hard objects such as iron wire to check the oil level and lubrication status of each gear oil, oil and butter. Pay special attention to the oil level of the triple oil cup not less than half, and regularly Observe the oil level change of the triplet. It is not normal for the fuel to be consumed or the fuel consumption is too fast (the knob of the triplet must be adjusted). The gear oil of the new machine is replaced half a year later. Lubricant is added at least once a week at the active part. Do not exceed half of the oil mirror, otherwise oil leakage will occur. 3. Prepare the materials and turn on the power and air pressure, raise the pressure cap to the upper limit position, then start the main motor motor, put in the prepared materials half a minute after the main motor starts, and then press the pressure cap to carry out the material Smelting. 4. If you need to change the color, please pour in the cleaning material or raw material cleaning agent, and then clean the old materials in the rotor shaft gap in the mixing chamber with a broom or iron wire. 5. According to the physical properties of the materials, the mixing can be adjusted automatically or manually. The hard materials should not be too large or too large, otherwise it will crash or burn out the main motor. 6. After the material is compacted, first raise the air pressure cover, then turn over the mixing tank, pour out the material after it is in place, and then return the mixing tank to the next batch. 7. When stopping production, first turn off the power of each function in turn, then turn off the power of the host, and then quickly clean up the mixing room and clean up the dust.
密炼片材挤出机,塑料片材设备 ( 图示 ) 注意事项： 徐州 恭乐橡塑机械有限公司的密炼机1、 定期检测各线路的绝缘效果，时刻注意机器警示牌上的警告内容。 V. Mixer sheet extruder, plastic sheet equipment ( illustration ) Note: Mixer of Xuzhou Gongle Rubber & Plastic Machinery Co., Ltd. 1. Regularly inspect the insulation effect of each line, and always pay attention to the warning signs on the machine. Warning content. 2. When the moving parts and the mixing chamber are blocked, do not reach inside with your hands or iron rods, but use plastic sticks to handle them carefully. 3. When touching hot parts, be careful not to get burned. 4. When there is powder leakage or the scream of the seal ring, first loosen the four screw caps evenly and screw them in, then add some material oil or oil to the rotor gap in the mixing chamber, and then idling 3— At the same time, use a hammer to gently tap the periphery of the seal ring gland around the spring for 5 minutes. If the powder leaks, adjust the tightness of the individual spring. If the seal ring gland and the side tank of the mixing chamber When it is very close, it means that the seal ring inside is worn and needs to be replaced again. For the method of replacing the seal ring, see the instruction manual. 5. Special attention: Check the gear oil, oil level and lubrication status of the oil before starting each day. Strengthen the daily attention that the oil level of the triple oil cup should not be less than half, and regularly observe the changes in the oil level of the triplet. Fuel consumption or excessive fuel consumption are abnormal (the knob of the triplet must be adjusted). The gear oil of the new machine should be replaced half a year later. Lubricating oil should be added at least once a week to the active part. Oil leakage will occur. 6. When the machine fails, stop the machine's movement within the first time. Unrelated personnel must not perform any action without authorization, and notify and wait for your company's machine maintenance personnel to inspect and repair.